Five-inch K-style gutters or 6-inch half-rounds, the most common residential sizes, are able to handle the rainfall on most houses in most parts of the country. But houses with big, steep roofs or those located in climates prone to heavy downpours may need wider gutters and extra downspouts to keep rainwater from overflowing.
What Size Gutters Do I Need?
To figure out what size gutters you need, first you’ll need to calculate the square footage of the gutter’s drainage area. For a simple gable-end roof, you would only need to make two calculations, one for each slope. Hip roofs and intersecting roofs have multiple facets, and for those you’ll need to add up the area (length x width) of each surface within a drainage area to get the total square footage.
How Do You Calculate Gutter Size?
Adjusting for Pitch and Rainfall
Once you know the total square footage of drainage for each gutter, you’ll need to adjust for the following two factors:
1. Roof-Pitch Factor
The steeper a roof’s pitch, the more windblown rain it can collect. You can measure pitch with a 2-foot level and a tape measure: Hold one end of the level against the roof, level it, and then measure the distance between the roof and the underside of the level at its midpoint, which gives you a 12-inch run. A 5-inch gap, for instance, is a 5-in-12 pitch. Once you know pitch, you can find your roof-pitch factor in the table below.
Roof pitch / Roof-pitch factor
- 12 in 12 or higher 1.3
- 9 in 12 to 11 in 12 1.2
- 6 in 12 to 8 in 12 1.1
- 4 in 12 to 5 in 12 1.05
- Flat to 3 in 12 1
2. Maximum Rainfall Intensity
The U.S. Weather Bureau records the maximum rainfall that could possibly happen in a 5-minute period, in inches per hour, for various regions. The higher the amount, the bigger a gutter has to be to keep from being overwhelmed in a storm burst.
Sizing the Gutters
Multiply the drainage area by the roof-pitch factor and rainfall intensity to find out the adjusted square footage. Then use the information below to see what size gutter you need. (If a roof’s various drainage areas call for different size gutters, go for the biggest one.)
K-Style
- 5-inch 5,520 square feet
- 6-inch 7,960 square feet
Half-round
- 5-inch 2,500 square feet
- 6-inch 3,840 square feet
For example: A house in Chicago has a roof whose actual drainage area is 1,000 square feet. The 6-in-12 pitch factor (1.1) multiplied by 1,000 yields an effective area of 1,100 square feet. Multiplying that number by the local maximum rainfall intensity (6.8 inches per hour) yields an adjusted square footage of 7,480 square feet. Therefore, this roof should be equipped with 6-inch K-style gutters.
Extra Capacity
What if the runoff is off the chart for standard gutters? You have three options:
- Get 7- or 8-inch gutters. They’ll cost more and probably require a custom order through a professional installer.
- Increase the pitch of the gutter. The standard is about ¼ inch per 10 feet. Increasing the pitch increases a gutter’s handling capacity, but the gutter may look askew over a long run.
- Add downspouts. The above recommendations assume that you have properly sized downspouts every 40 feet. As with gutters, a downspout’s capacity must match or exceed the expected runoff. Use the chart below to figure out how many extra downspouts you need. Adding a 2 by 3 rectangular downspout, for instance, boosts your gutter’s capacity by 600 square feet of drainage area.
Rectangular
- 2 by 3 inches = 600 square feet
- 3 by 4 inches = 1,200 square feet
Round
- 3 inches = 706 square feet
- 4 inches = 1,255 square feet
Our Conclusion
Properly sized gutters help protect several key parts of your home from water damage—including your roof and foundation. Fortunately, choosing the right size gutter can be relatively simple. All you need to do is determine your home’s drainage area, roof-pitch factor, and maximum rainfall intensity and multiply those three numbers together.
If you are not confident in your calculations or want an expert opinion, call a reputable gutter company. These professionals can offer recommendations, provide a personalized quote, and handle the entire installation process—including the addition of gutter guards and other upgrades.
Information courtesy of the Sheet Metal and Air Conditioning Contractors National Association (SMACNA), a standards-setting organization based in Chantilly, Va.