We may be compensated if you purchase through links on our website. Our Reviews Team is committed to delivering honest, objective, and independent reviews on home products and services.
If you don’t have adequate access to electricity in your house, adding an electrical outlet is a simple way to improve your home’s functionality. This DIY project may seem straightforward, but it requires careful planning to ensure you comply with electrical codes. In the video above, master electrician Allen Gallant shares insider tips for the installation process. In this guide, we’ll walk you through the steps to add an electrical outlet
Gathering Tools and Materials for Adding an Electrical Outlet
Before you begin the installation process, make sure you have all the necessary tools and materials. For this project, you’ll need the following tools and materials:
- 1/2-inch drill bit
- 5/8-inch extended spade bit
- Cover plate
- Drill/driver
- Drywall saw
- Electrical box
- Electrical cable
- Fish tape
- Flashlight
- Linesman pliers
- New outlet
- Safety glasses
- Screwdriver set
- Wire stripper
Choosing the Right Location For Your Outlet
The location of your new outlet can have a big effect on your DIY installation process. Consider these factors when deciding where to place your new outlet:
- Accessibility for intended use: Make sure the outlet is easily accessible for the appliances or devices you plan to plug in. Placing it too high or low or in an inconvenient spot could make everyday use difficult.
- Building codes and regulations: Ensure the outlet’s location complies with local electrical codes, especially in areas like bathrooms, kitchens, or outdoors, where specific regulations might apply for safety reasons.
- Proximity to existing power sources: Position the new outlet close to the existing wiring to simplify installation and reduce the need for extensive rewiring.
- Structural elements like studs and joists: Be mindful of the placement of studs, joists, or other structural components in the wall, as they can affect where and how easily the outlet can be installed. Choose a location that allows for easy routing of electrical cables without any major obstacles.
Safety Precautions
Safety should always be your top priority when working with electricity. The following steps are a good place to start, but when in doubt, refer to the Occupational Safety and Health Administration’s guide to working safely with electricity.
Turning Off the Power
Before you begin any electrical work, turn off the power to the room where you’ll be installing the new outlet. Locate your home’s main electrical panel and switch off the circuit breaker that controls power to the area where you’ll be working.
Using Proper Safety Equipment
Always wear safety glasses to protect your eyes from debris when drilling or cutting. Use insulated tools and wear rubber-soled shoes to minimize the risk of electrical shock. Also, turn on enough lighting in your workspace to see clearly.
Checking for Live Wires
Even after turning off the power, use a voltage tester to double-check that the wires you’ll be working with aren’t live. Take your time to verify that the wires are completely safe before proceeding with the work.
Step-by-Step Electrical Outlet Installation Process
Now that you have your materials ready to go, you can begin the installation process. Reference the video above as needed. Follow these steps carefully to add your new electrical outlet:
- Measure to find the location of the new outlet.
- Drill down through the floor and into the basement at the new outlet location.
- Measure over from the drill bit poking into the basement to locate the nearest stud bay.
- Cut a hole for the new outlet box in the baseboard or wall.
- Drill down through the outlet box hole and into the basement with an extended spade bit.
- Feed fish tape down the hole, attach an electrical cable to the tape, then pull the cable into the room.
- Strip the outer insulation from the cable.
- Pull the cable into the electrical box, then tighten the cable clamp.
- Wrap the bare copper wire clockwise around the green grounding screw inside of the box and tighten the screw.
- Screw the electrical box to the wall.
- Attach the white wire to the silver screw on the outlet.
- Attach the black wire to the brass screw on the outlet.
- Attach bare copper wire to the green grounding screw on the outlet.
- Wrap electrical tape around the outlet to protect the wire connections.
- Screw the outlet to the electrical box, then install the cover plate.
- Have a licensed electrician connect the cable to an existing circuit or to the main electrical panel.
Allen Gallant demonstrates these steps, showing how to navigate challenges such as drilling through floor joists and feeding wire through wall cavities for a smooth and efficient installation.
Testing the New Electrical Outlet
Before restoring power and plugging in your appliances, check that all wire connections are secure and that no bare wire is exposed. Then, try a quick power test by doing the following:
- Turn the power back on at the main electrical panel.
- Use a circuit tester to verify that the outlet is receiving power.
- Plug in a small appliance or lamp to confirm the outlet is working properly.
If everything checks out, you’ve successfully installed your new electrical outlet. If there are any issues, turn off the power immediately and recheck your wiring connections for any mistakes.
Common Challenges and Solutions To Adding an Electrical Outlet
While adding an electrical outlet can be a straightforward process, you may encounter some challenges along the way. Here are some common issues and how to address them.
Navigating Obstacles in Walls
When drilling or cutting into walls, you may run into obstacles like pipes or existing wiring. Use a stud finder with a wire detection feature to locate potential obstructions before cutting or drilling. Be sure not to damage any existing infrastructure within the walls.
Dealing With Older Wiring
In older homes, you may encounter outdated wiring systems. If you come across knob-and-tube wiring or aluminum wiring, consult a licensed electrician before proceeding. This wiring requires special handling and you may need to update it to meet current codes.
Limited Access to Power Sources
If the nearest power source is a far distance from your desired outlet location, you may need to run wiring through multiple wall cavities or floors. If that’s the case, consider hiring a professional for installation. Long wiring runs can make the project more complex, so it’s best to leave it to the professionals.
When To Call a Professional To Add an Electrical Outlet
While many homeowners can successfully add an electrical outlet with this DIY process, there are situations where it’s best to call in a licensed electrician. Consider professional help under the following conditions:
- If local codes require a permit or professional installation
- If you need to upgrade your electrical service to accommodate the new outlet
- If you’re unsure about any step in the process
- When connecting to the main electrical panel
- When working with outdated wiring
If you’re not comfortable working with electrical systems or if you encounter unexpected issues, it’s better to be safe than sorry. Call a local electrician to install your electrical outlet so your home wiring is safe and reliable for years to come.